冷庫根據現場的使用要求和通道寬度的限制有推拉門，平移門，電動門，卷閘門，彈簧門等形式，其中最常見的就是推拉門。
Cold storage according to the site requirements and channel width restrictions, there are sliding doors, translation doors, electric doors, roll gate, spring door and other forms, of which the most common is the sliding door.
平移門主要用于通道寬度受到限制，推拉門無法完全打開以及需要比較大的通道時，門可以做到比較大，大的設備與搬運工具可以自由出入。
The translation door is mainly used for the limitation of the channel width, the sliding door can not be fully opened and the larger channel is needed, the door can be made larger, and the large equipment and the transporting tool can freely enter and leave.
冷庫由于要做隔熱層，一般為保護隔熱層會做到高于地面3-5厘米距離，加上隔熱層的厚度，與外面的完成地面形成臺階，但這種結構安裝和搬遷比較方便;另外一種是將冷庫內部與外部地面完成而做成一樣高，甚至在隔熱層之上用同樣地面材料制作，這樣冷庫無法搬遷，但人及搬運工具進出冷庫比較方便。
Due to the cold insulation protection for general insulation layer will be higher than the ground 3-5 cm distance, thickness of insulating layer coupled with the outside of the ground to form a complete step, but the structure is convenient installation and relocation; another is the cold inside and outside ground and made the same high, even in the heat insulating layer by making the same above ground material, so cold and unable to move, but the handling tool import and more convenient storage.
每個冷庫獨立使用一套庫體，六面體每一面分別設計隔熱結構，與外界空間分離，這種結構安裝方便，搬遷安裝也容易。
Each refrigeratory independently uses a set of warehouse bodies, and each side of the hexahedron is respectively designed with heat insulation structure, which is separated from the outer space. The structure is easy to install and easy to move and install.
兩個或以上冷庫共用相鄰庫體部分，在相鄰庫體可開門連通也可單獨開門，獨立使用，這種結構在安裝時和搬遷時都需要較高的精度，但可以節約庫體隔熱材料的用量。
Two or more adjacent storage shared library body part in the adjacent base body can open the door can also be individually connected to open the door, independent use, this structure is high in the installation and removal of the accuracy, but can save the amount of insulation material storehouse.
一般冷藏庫庫溫在零下22℃的庫板用100mm厚隔熱層，零下22℃以下的冷庫要用150mm厚的隔熱層。零下30℃以下采用200mm毫米厚的隔熱層。
General refrigerated Kukuwen in Library Board - 22 C with 100mm thick insulation layer, minus 22 DEG C to use cold storage insulation layer thickness of 150mm. Use 200mm mm thick insulation layer below 30 degrees below zero.
隔熱材料一般采用環保聚氨酯發泡材料，也有的用聚苯乙烯發泡材料。成型基板板材的選擇：前常用發泡成型的外表保護材料主要有彩鋼板，鍍鋅鋼板，花鋁板，在較高要求的場合或特使用途的場合會用到不銹鋼板。
Heat insulation material usually adopts environmental protection polyurethane foaming material, and others use polystyrene foaming material. The choice of forming substrate sheet: before the general use of foam forming surface protection materials, mainly color steel plate, galvanized steel sheet, flower aluminum plate, in higher demand occasions or special envoy occasions will use stainless steel plate.
本文由食品冷庫為您提供，我們的網站是:http://www.sddslk.com/我們將以全心全意的熱情為您提供更優質的服務，歡迎您的訪問!
This article from the food cold storage for you, our website is: http://www.sddslk.com/, we will wholeheartedly provide you with better quality of service, you are welcome to visit!
魯公網安備 37010402001149號 網站地圖 XML
